Filter Results By:
Products
Applications
Manufacturers
In-line
In-line test equipment is specifically designed for testing production items on the manufacturing line.
- Virginia Panel Corporation
product
S6 - 6 Module Solution
Low profile with 1,440 contact points while only using 1U of rack space. Ideal for in-line test applications. Horizontal layout maximizes module positions and minimizes required rack space.
-
product
Clamp-On Ultrasonic Flow Monitor
KATflow 10
The KATflow 10 is a simple ultrasonic clamp-on flow monitor, which provides an extremely cost-effective alternative to in-line flowmeters on effluent, wastewater and sludge applications. The KATflow 10 is used to monitor the flow of liquids containing higher levels of solids or entrained gas bubbles for measurements where a general flow indication is sufficient. The instrument is extremely simple to install and commission and is ideal for applications which demand good repeatability and reliable results.
-
product
ClearLine Level Switch
The ClearLine in-Line fluid detector is a point level switch that mounts directly into the process piping between two flat-faced flanges. This product is best suited for pump protection and low-level indication below vessels.
-
product
Deluxe Fused Voltage Leads
DFV
PowerSight DFV is a set of voltage leads that have in-line fuses. For added safety if a voltage lead shorts to ground via a cut in the insulation. Suitable for use to 1000V, includes replaceable fuses.
-
product
Digital TV Signal Meter
King SureLock
Pinpoint the location of local DTV towers. Point the antenna before scanning for channels. Saves time and frustration. Eliminate the need for multiple channel scans. Takes the guesswork out of finding the towers. Simple to use, plug-n-play design. Connects to the antenna TV output or in-line. Positive signal identification. LED lights indicate where DTV signal is strongest. Variable sensitivity adjustment. Foolproof antenna pointing in both strong and weak signal areas.
-
product
Dimensional Metrology
Nova Measuring Instruments Inc.
Nova offers in-line optical integrated and stand-alone metrology platforms. The metrology product portfolio, combined with our modeling algorithm software, delivers unique measurement capabilities for the most advanced semiconductor technology nodes.
-
product
EDFA Amplifier
A line of Gain Flattening Erbium-Doped Fiber Amplifiers are designed for in-line amplification of DWDM networks. When a standard EDFA is used to amplify multi-channel DWDM signals, the output power level of various channels will vary according to the gain profile of the erbium fiber. This gain variation can be as great as 6 dB in magnitude. The EDFA-GB-R is unique in its dual-stage amplification and internal Gain Flattening Filter (GFF) to compensate the erbium fiber gain variation.
-
product
FIBER OPTIC MICROSCOPES
SpecVision
SpecVision is a video probe that engages directly with Krell polishing machines. This permits the viewing of polished optical surfaces while connectors or bare fibers are still loaded in the polisher. This in-line video inspection technique minimizes material handling and potential damage/contamination that may occur when transferring components from the polisher to a traditional microscope. SpecVision can interface with Scepter, SpecPro and Rev Polishers.
-
product
Fiber TAPs
Profitap fiber TAPs provide secure in-line network access for the monitoring of 1–400 Gbps fiber networks. By splitting the light flowing on the network link, fiber TAPs deliver an exact copy of the data for real-time monitoring and analysis, without disrupting the network. Passive fiber optic TAPs require no power, and therefore introduce no point of failure when deployed in a network.
-
product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Fibre Channel XMC Interface Module
XMC-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Flow Tube
913
The Meech Model 913 Flow Tube is designed to neutralise static charges on materials in handling and conveying systems. It incorporates in-line ionisation, which eliminates material clinging and clogging in ducting systems due to static charges.
-
product
Full 3D Inline Metrological & Imaging AOI
Metrological Full 3D AOI is achieved by measuring all 3 dimensions (X, Y and Height) to detect every measurable solder and component defect pre-reflow and/or post reflow soldering.
-
product
Gas Analyzers
Mobile, Table Top, Inline, Ambient Air Monitoring and Moisture Measurement gas analysers.
-
product
General Purpose
Columbia Research Laboratories
This group of accelerometers is made up of the 3000 and 5000 Series. The 3000 Series are standard size units, including many with all welded construction, that are hermetically sealed for use in dirty and humid environments. The 5000 Series are smaller and lighter in weight than standard units. Characteristics are almost identical except that with miniature units higher natural frequencies and shock levels can be obtained due to their inherently reduced mass. Sensitivities, however are somewhat lower. High Temperature models are available that operate to +500°F. For best performance use with the Columbia Model 4601 Charge Amplifier or Model 5810 Inline Charge Converter.
-
product
Grain Inspector
iS-G1
The iS-G1 is a full line speed optical module for the inspection of crystal grains.Using our new grain imaging technology, the iS-G1 is able to inspect as cut wafers at full inline speed with no need to stop the conveyor belt. Automated algorithms analyze the grains and report metrics.
-
product
Handheld Digital Multimeter, 2000 Count, Auto/ Manual, 10 A, 250 V, 3.5 Digit
72-13430
*Clear LCD Display*Equipped with comfortable protective cover, test probe holder*2m drop test, precision protection*Auto Power Off*Auto Backlight Off*Loud Buzzer Sound*Knobs shift smoothly, in-line with ergonomics*Relative mode*Powered by AAA 1.5V x 2 batteries*12-month limited warranty *view Terms & Conditions for details
-
product
Handheld Digital Multimeter, AC/DC Voltage, Continuity, Diode, 3.5, 2000, Manual, 250 V
72-13440
*Palm size digital multimeter with 2000 count clear LCD display*CAT II 250V environment safety rating*Manual functional select and manual range selection*2m drop test, precision protection*Auto backlight off*Knobs shift smoothly, in-line with ergonomics*Equipped with comfortable protective cover and test probe holder*Powered by AAA 1.5V x 2 batteries*Non-contact voltage (NCV) detection*12-month limited warranty *view Terms & Conditions for details
-
product
Handheld Digital Multimeter, AC/DC Voltage, Continuity, Diode, Resistance, Temperature, 3.5, 2000
72-13435
*Clear LCD Display*Equipped with comfortable protective cover, test probe holder*2m drop test, precision protection*Auto Power Off*Auto Backlight Off*Loud Buzzer Sound*Knobs shift smoothly, in-line with ergonomics*Powered by AAA 1.5V x 2 batteries*12-month limited warranty *view Terms & Conditions for details
-
product
High Mix High Component Count Or LED Panels
MC388
The MC388 features four simultaneous heads with dual-vision alignment that can achieve placement rates of 10,500 CPH. When used as an inline machine, up to 192 Smart Feeder can be attached, providing a near-zero job changeover time. Plus, it has the huge placement area, high precision, and accuracy that users have come to expect from MC-series component placers. The MC388 is ideal for LED strips, drivers, or other large, high-component panels.
-
product
High Precision Inline Stencil Printer
AP430
With the features, performance, and build-quality of systems twice its price, Manncorp's AP430 Fully-Automatic Inline Stencil Printer brings affordability to leading-edge, solder paste printing technology. Capability for 01005 chips, µBGAs, and 12-mil ultra-fine-pitch components is now at a price point that will fit even the most modest budgets of surface mount manufacturers who require full automation and high throughput.
-
product
HJT Tray Automation
JRT Photovoltaics GmbH & Co. KG
The highly sophisticated machine platform HJT TRAY AUTOMATION ensures the fully automated loading and unloading of trays for inline-coating processes. Outstanding innovation is the particularly surface-friendly, yet high-performance handling of wafers in inline flat-carrier transport. This involves high-precision, row-by-row positioning of the wafers which are individually measured.
-
product
In-Line 1553 Ethernet Converter
NLINE-E1553
Full BC, RT, and BM 1553 Controls Built-in a Small, Rugged, In-Line package. Control and convert 1553 messages to/from Ethernet in real-time (<20 uSec). Auto-bridge 1553 messages (BM) to UDP Ethernet without any programming.
-
product
Inline Barcode Verifiers
DataMan 475V Series
Cognex barcode verification technology ensures the readability and compliance of 1D and 2D barcodes to industry standardization guidelines. Today most companies spot check codes one at a time using an offline, operator-based verifier which can be slow and cumbersome.
-
product
In-Line / Board Handler
Circuit Check’s in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading ICT handlers including Keysight 5i, Teradyne TSh Multi-Site, IPTE and Pematech. Circuit Check is the go-to partner for in-line functional test fixtures to speed production throughput.
-
product
Inline DC Panel Meter Kit
The Inline DC Panel Meter Kit has all the bits you need to create an elegant, seamless DC volt/ameter. Measuring current usually means interrupting the VCC or ground return path, and 'interrupting' usually means cutting. We designed the kit to be used 'inline' - no need to cut wires just plug your wall wart into the kit and the kit into your target device. We found it to be really handy to measure various 12V devices (routers, WiFi APs, etc) up to 10 amps.
-
product
Inline Density Meters
DM-Series
The DM-Series Inline Density Meters allow for continuous monitoring and process control of a variety of solutions. The fully integrated, low-maintenance configuration allows the DM-Series to be used in a variety of critical applications where precision and reliability are required. The DM-Series is a cost-effective, long-term solution for continuous density measurement.
-
-
product
In-Line Functional Test Fixtures
Add an advantage to in-line production with fast change over interchangeable fixturing. Circuit Check’s in-line board handlers and in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading handlers.
