Filter Results By:
Products
Applications
Manufacturers
-
product
Chip Inspection System
GEN3000T
GEN3000T is an inspection system that performs automatic inspection of individual semiconductor chips.This revolutionary chip surface inspection system was achieved by combining the chip handling technology cultivated by Toray with the inspection algorithm used in the "INSPECTRA®" wafer defect inspection system.
-
product
Wafer Chip Inspection System
7940
Chroma 7940 wafer chip inspection system is an automated inspection system for postdiced wafer chip inspection.
-
product
High Soeed CMOS System on Chip (SoC) Line Scan Image Sensor
LS4k
The LS4k is a high speed CMOS System on Chip (SoC) line scan image sensor optimized for applications requiring short exposure times and high accuracy line rates. It incorporates on chip two pixel arrays consisting of 2 rows with 4,096 7µm pitch pixels and 4 rows with 2,048 14µm pitch pixels respectively, a high accuracy (12-bit) high speed (84MHz) analog-to-digital conversion (ADC), and sophisticated on chip optical calibration for PRNU, DSNU, and lens shading correction.
-
product
In-Process Wafer Inspection System
7945
Chroma 7945 wafer chip inspection system is an automated inspection system for pre and post diced patterned wafers. Change kits enable switching between various applications by allowing different carriers including metal frame or grip ring.
-
product
USB2.0 Module With 2 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation of Avionic ARINC825/CAN Bus Systems
APU825-2
USB2.0 module with 2 CAN bus nodes ARINC825 compliant for testing and simulation of Avionic ARINC825/CAN bus systems.
-
product
AIM System Solutions
AIM can provide a wide range of customized solutions:*Special-to Type Test Equipment (STTE)*High Level Bus Analysers (HLBA)*Data Acquisition Recording & Simulation Systems*Aircraft Ground Equipment (AGE)*MIL-STD-1760 Weapon Test Sets*Fibre optic MIL-STD-1553 Stub/ARINC429 Link Extension System (FoMIS/FoL)
-
product
6U VPX Direct RF Processing System
VP460
The VP460 is designed to enable customers to begin development of their next generation systems using revolutionary new processor technology. It is in alignment with the SOSA™ Technical Standard to provide the interoperability required by the US Air Force, Army and Navy.
-
product
Computing VITA System
CRS 48.5
The CRS 48.5 is a complete, integrated, pre-tested, ready-to-run HPEC rugged subsystem enabling faster development/deployment at lower cost and risk using the most advanced VITA 48.5 compliant air-flowthrough cooling to allow the integration of up to eight quad core Intel® Core™ i7 processing nodes.
-
-
product
Data Processing System
CRS-D8I-3VF1
The CRS-D8I-3VF1 VPX system’s I/O flexibility is capable of meeting a large number of configurations. It is designed to support Abaco Systems’ Intel 3rd generation Core i7 3U SBCs, Gigabit Ethernet switch, video compression card, CUDA-based graphics cards and a MIL-STD-1553/ARINC429 multi-protocol card.
-
product
COTS Systems
Pre-integrated to save you time and money, pre-validated systems proved an optimum computing platform for mission applications.
-
product
Development System
PCIe490
The PCIe490 Expansion Chassis enables users to scale application workstations with up to eight additional PCIe boards per chassis and up to 63 total slots with chassis daisy chaining. It was designed to accommodate the Abaco Systems PC820 and PC821 with Xilinx Ultrascale technology and multiple FMC+ interfaces.
-
product
FMV Compression System
daq8580
The Daq8580 is designed to address the challenges of processing, transporting and storing full motion video through video encoding, and can interface with a wide variety of analog and digital I/O and process standard video formats up to 1080p30 as well as computer resolutions up to 1600x1200.
-
product
Mezzanine System
5033
ECM P/N 5033 provides eight channels of RS485 / RS422 I/O. The 110 ohm termination for each channel is enabled or disabled in software. Disabling termination saves power by eliminating unneeded or redundant termination. Speeds of up to 20 Mega bits per second are possible, but this design also features a 250K bits per second slower edge rate mode. The 250K bit mode is valuable when EMI is more of a concern and throughput is not important. All channels power up as inputs with the outputs disabled.
-
product
Mezzanine System
3556
The 3556 provides two removable Micro SD flash memory sites, and fourteen bits of general purpose digital I/O. The Micro SD sites are each capable of Gigabytes of storage. A retention mechanism holds the Micro SD card securely in place preventing movement due to vibration or shock.
-
product
Mezzanine System
5174
The 5174 provides two major functions, serving as a precision Voltage Controlled oscillator board and a variable frequency source board. These features can be use together or independently. As a variable frequency source, the 5174 provides a high-resolution variable clock source that is based upon a reference clock supplied by the ECM carrier.
-
product
Mezzanine System
5362
ECM P/N 5362 provides eight channels of LVDS I/O with fixed 100 ohm termination. Speeds are up to 200M bits per second. All channels power up as inputs. Software can then enable outputs on a channel by channel basis.
-
product
Mezzanine System
5188
ECM P/N 5188 provides an AD8109 crosspoint switch for analog or digital signals with 250MHz of Bandwidth. For single ended applications 8 inputs can be connected up to 8 outputs in any configuration.
-
product
Mezzanine System
5676
The Abaco SystemsP/N 5676 ECM module provides eight channels of 16 bit voltage measurement in the 0 to 2.5V volt range. For each channel the common mode voltage range is -100 volts to +100 volts.
-
product
Mezzanine System
5181
ECM P/N 5181 uses TI TLV320AIC23 high resolution audio codecs to provide two channels of Audio input and two channels of Audio output. Each input channel consists of two inputs a left and a right, and each output channel consists of two outputs left and right. The outputs are muteable.
-
product
VPX Processing System
CRS-D4I-3VB1
4-slot, SWaP-reduced, rugged VPX Intel base plate cooled data processing system that can be applied across various applications including civilian and military unmanned vehicles, manned commercial and military aircraft, helicopters, over- and underwater research vessels, ground vehicles, and locomotives.
-
product
Mezzanine System
5235
The 5235 ECM provides 16 bits of simple digital I/O. The digital I/O is connected directly to the digital I/O on the carrier card. Inputs are clamped to about 3V by FET buffer ICs, and are 5V tolerant.
-
product
Mezzanine System
5181 MMS ECM
ECM P/N 5181 uses TI TLV320AIC23 high resolution audio codecs to provide two channels of Audio input and two channels of Audio output. Each input channel consists of two inputs a left and a right, and each output channel consists of two outputs left and right. The outputs are muteable.
-
product
VPX Development System
VPX370 3U
The VPX370 is a second generation VPX development platform that delivers, performance, flexibility, and scalability all in a compact 3U VPX form factor.
-
product
Mezzanine System
3560
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
product
Mezzanine System
5041
ECM P/N 5041 provides eight channels of RS485 / RS422 I/O with fixed 120 ohm termination for each channel. Speeds are up to 30M bits per second. All channels power up as inputs. Also transceiver inputs are always enabled for loop back diagnostic use when the outputs are enabled. Software can enable outputs on a channel by channel basis.
-
product
Mezzanine System Carrier
MMS6245
The MMS6245 gives you the ultimate flexibility in rugged embedded I/O by allowing you to customize the 64 user-configurable front panel signals with our patented Electrical Conversion Module (ECM) technology. This configurable XMC carrier can host up to four ECMs giving you the ability to customize I/O to your specific needs.
-
product
Mezzanine System
5158
The 5158 Electrical Conversion Module (ECM) provides eight (8) RS-232 outputs and eight (8) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
product
Mezzanine System Carrier
MMS8010 / MMS8011
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
product
Mezzanine System
5658
ECM P/N 5658 provides eight channels of 16 bit current measurement in the 0 to 25 milli-amp range. Each channel allows independent common mode voltages from -100 volts to +100 volts. Current detection is accomplished with a precision 100 ohm current sense resistor, creating a voltage drop of 2V in the current loop at 20 milli-amps.
