Filter Results By:
Products
Applications
Manufacturers
- CAMI Research Inc. (CableEye®)
product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
CAMI Research Inc. (CableEye®)
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester. This software assigns test point numbers to connector types and applies standard pin designations to the pin numbers. For each custom connector, first choose a connector graphic from our large library to match your connector. Then touch the tester probe to the connector pins one-by-one to automatically detect and assign a test point to each pin. A synthetic voice reads probed pins as you touch them so you don’t need to take your eyes off the connector you’re probing. Finally, enter pin labels of your choice if you wish to override the standard designations.
-
product
Test Adapter
cPCI/VME/VME64x
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
product
Test Adapter
Development of a 12-way test and programming adapter from Toptest for ?? The Dash ?? from Bragi, a wireless, intelligent earphone with communication and sensor technology. With the first version of the test adapter, only a purely sequential testing was possible due to the interdependencies of the tests. In version 3.0, the now autonomous tests were brought into a parallel TestStand sequence. In addition, individual sockets were prioritized in order to optimally use the hardware resources. This resulted in a time advantage of 80% compared to the initial situation.
-
product
Test Adapters
Range of products with DIN-connectors type B, C, D, E, F and M. Voltage/current measuring fields, wire wrap pins or jumper/bridge fields. Mechanical sets and guide rails to configure your own 6 or 9 U Test Adaptor from the wide range of 3 U Test Adaptors.
-
product
Test Adapter
PMC-UNIV-TEST
PCI adapter for PMC with options for PCI and PMC Stack Pass through connections
-
product
Test Adapter
Ramcheck 100
This addition to the RAMCHECK memory tester provides needed support for testing of SDRAM and standard EDO/FPM DRAM 100-pin SO DIMM modules at an affordable price.
-
product
Test Adapter
Ramcheck 72 Pro
Our latest addition to the RAMCHECK memory tester provides needed support for testing 72-pin SO DIMM modules used in older laptop computers. The RAMCHECK memory tester automatically detects the presence of the RC 72 Pro adapter
-
product
Test Adapter
FECVF1600
Frothingham Electronics Corporation
The VF1600 Test Station is a high current forward pulser designed to be used in conjunction with our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of much higher forward current. The VF1600 station can produce a maximum current of 1600A at up to 5V using an 8.3 mS half sine waveform at the built in test station, and THETA and DVF tests at up to 500A at 10mS pulse width. It is derated for wider pulses. For rectangular VF pulses at 300us or 1ms, it can produce up to 2000A. The station can also test all of the usual FEC200 tests in the same test program.
-
product
Test Adapter
RAMCHECK® SIMM
The RAMCHECK SIMM Adapter is another addition to the RAMCHECK memory tester. It provides a needed solution for testing older 72-pin EDO/FPM DRAM SIMM modules. An optional adapter for 30 and 72-pin SIMMs is also available
-
product
Test Adapter / Pneumatic Adapter
GPS testing technology offers a wide range of pneumatic adapters. The support with compressed air results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.
-
product
Test Adapter / Vacuum Adapter
GPS testing technology offers a large selection of vacuum adapters. The support with vacuum (negative pressure) results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.We recommend the use of vacuum hoods or, if contact is required on both sides, our vacuum swivel hood.
-
product
Test Adapters/ Mechanical Interchangeable Adapters
GPS Prüftechnik offers a wide range of mechanical adapters. These are mostly used for functional tests.
-
product
HF test adapter
High-frequency test adapters (HF adapters) from INGUN are designed as a replacement set system, consisting of a manual test adapter (MA 21xx and 32xx series) and a high-frequency shielded replacement set from the ATS MAxx/HF series.
-
product
Vacuum Test Adapter
Vacuum test adapters (VA) are suitable for contacting electronic assemblies with large quantities (mass testing) and a small number of variants. INGUN vacuum test adapters are available as standard as a single system without an exchangeable replacement kit.
-
product
Pneumatic Test Adapter
Pneumatic test adapters from INGUN are particularly suitable for contacting medium-sized electronic assemblies (series testing) and a large number of variants. The test adapters are designed as a replacement kit system, are connected to an existing test system and operated with replacement kits that are specially designed for the electronic assembly to be tested.
-
product
Chip Test Adapter
RAMCHECK Sync
The RAMCHECK Sync Chip Adapter tests popular TSOP SDRAM memory chips in sizes of 16Mx16, 4Mx16, 32Mx8, 8Mx8, 64Mx4, 16Mx4 and more. Picture above shows the adapter with all optional sockets for 54, 50 and 44-pin.
-
product
Test Adapter / Extender
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly.
-
product
Test adapter HR-LR
MA-HL02
Hachmann Innovative Elektronik
Our test adapter MA-HL02 connects LR measuring devices to standardized HR string parts. Due to small dimensions and skid-proof design it's easy for him to catch up with everything.
-
product
Test adapter MR-LR
MA-ML01
Hachmann Innovative Elektronik
Our Test adapter MA-ML01 connects LR measuring devices to standardized MR string parts. Due to small dimensions and skid-proof design it's easy for him to catch up with everything.
-
product
Manual Test Adapters
Manual test adapters (MA) from INGUN are available in several series and series, which differ in terms of use, maximum permitted contact force, parallel stroke, size and service life.
-
product
Engine Test Adapters
Atec has built test adapters for a wide variety of engines from high bypass fan engines to small APU engines. Testing a new engine type in your existing jet engine test cell can be challenging, and upgrade modifications will be needed. Atec does not view an adapter as just a mechanical weldment that simply mates the engine to the aeroengine thrust stand. Our engineers realize that additional items will be needed in the facility to insure total project success. During the planning phase, Atec engineers can visit your existing facility and/or review videos to make a comprehensive assessment of the integration needed to add a new engine type to your testing facility. Atec can perform airflow, acoustics, FEA and sub systems analyses to ensure that any new engine added to your jet engine test cell will have the proper capacity to perform properly. Vital Link’s current experience with advanced fighter engines test adapter kits further bolsters our expertise in high thrust engine test handling.
-
product
Manual Test Adapter
linear pin compressionhinged carrier for probe cardfacilitated probe tower positioningmounted onto test head stiffener
-
product
Chip Test Adapter
SOJ EDO/FPM
Our new addition to the RAMCHECK line provides support for common 20 to 42-pin EDO/FPM DRAM SOJ chips of sizes 256Kx16/18, 1Mx16/18, 8Mx8, 16Mx4, 2Mx8, 4Mx4, 16Mx1, 1Mx4, and 4Mx1.
-
product
Interface Test Adapter
ITA
Circuit Check is focused on the military and aerospace market. Our solutions are delivered according to a rigorous set of test requirements and quality metrics. The Circuit Check staff of engineers follow a defined Project Management process to control the project deliverables,manage the scope, and meet the quality needs for in-field serviceability and test system longevity.
-
product
Test Adapters / Aeroflex Test System
52xx / 5300
We develop and manufacture test adapters for your existing interface including documentation and test program
-
product
Respirator Fit Test Adapters
TSI Fit Test Adapters for PortaCount Respirator Fit Testers provide an easy, practical alternative to the probed method of quantitative respirator fit testing. Respirator Fit Test Adapters enable quantitative fit testing for individuals wearing their own respirators. Use the Fit Test Adapters spreadsheet to find the right fit test adapter. You can search for respirator manufacturer, the respirator model, and in some cases, the respirator’s filter/regulator connection. Click on the links in the document, or below, to see more details about a fit test adapter and your purchase options.
-
product
K-Base Test Board Adapter
1180
The TESCO K-Base Test Board Adapter allow quick, convenient testing of self-contained K-Base meters on test boards designed for socket type meters. The K-Base Test Board Adapters are designed for single phase (Catalog No. 1180-2) and polyphase (Catalog No. 1180-4).
-
product
A-Base Test Board Adapter
1182 and 1183
From time to time, you may find yourself needing to test A-Base meters. Or perhaps you will need to test them for the first time in years as part of a removal project. Well, TESCO can help with the A-Base Test Board Adapter!
-
product
Test Fixture Adapters for In-Circuit Test Fixtures
Circuit Check test fixture adapters are utilized when the target ICT tester is not available or has been replaced with a newer technology tester. The tester adapter will often allow existing test fixtures from one test manufacturer to be utilized on another manufacturer test platform, eliminating the need for replacement fixtures. Contact Circuit Check to discuss your tester and fixture combinations for the best choice of a cost effective solution.